KWiki

User Tools

Site Tools

Trace:
microct

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
microct [2021/07/15 23:53] – [Stepper Motors] konstantinmicroct [2022/03/05 13:12] (current) – [FDXD-1417] konstantin
Line 3: Line 3:
 ===== X-Ray Source ===== ===== X-Ray Source =====
  
 +==== PSX10-WB-130 Microfocus Source ====
 +
 +  * 20kV-130kV targe voltage
 +  * 0.356mA@45kV 0.123mA@130kV beam current
 +  * 7µm@4W - 21µm@16W focal spot on tungsten target
 +  * 115° cone angle
 +  * 0.51mm Beryllium window
 ==== PXS5-724EA Microfocus Source ==== ==== PXS5-724EA Microfocus Source ====
  
Line 38: Line 45:
 ===== X-Ray Detector ===== ===== X-Ray Detector =====
  
 +==== FDXD-1417 ====
 +[[fdxd1417|Pins]]
 ==== Dexis Platinum / GXS-700 ==== ==== Dexis Platinum / GXS-700 ====
   * SN: 0104430711   * SN: 0104430711
Line 75: Line 84:
   - (BL) RS422 A   - (BL) RS422 A
   - (WH) RS422 B   - (WH) RS422 B
 +
 +=== Power Supply ===
 +  - 5V (2A) 
 +  - +/- 15V (700mA)
 +
 +=== Protocol ===
 +  - 8MHz UART, 1 Start bit, No Stop bit
 +  - ADC Data is 12bit + 1 control (seems to be always 1)
 +  - Data is streamed out pixel by pixel, line by line, 1244x 13 bit data packets per CCD line
  
 ==== Flatpanel Detector ==== ==== Flatpanel Detector ====
Line 85: Line 103:
  
 https://github.com/gnea/grbl/wiki/Grbl-v1.1-Configuration https://github.com/gnea/grbl/wiki/Grbl-v1.1-Configuration
 +
 +http://eleccelerator.com/fusecalc/fusecalc.php?chip=atmega2560
 +
 +== Settings ==
 +
 +M1: /dev/USB1
 +  * $0=10
 +  * $1=25
 +  * $2=0
 +  * $3=2
 +  * $4=0
 +  * $5=0
 +  * $6=0
 +  * $10=1
 +  * $11=0.010
 +  * $12=0.002
 +  * $13=0
 +  * $20=1
 +  * $21=0
 +  * $22=1
 +  * $23=7
 +  * $24=500.000
 +  * $25=500.000
 +  * $26=250
 +  * $27=1.000
 +  * $30=1000
 +  * $31=0
 +  * $32=0
 +  * $100=25.000
 +  * $101=200.000
 +  * $102=200.000
 +  * $103=250.000
 +  * $110=1000.000
 +  * $111=500.000
 +  * $112=500.000
 +  * $113=500.000
 +  * $120=20.000
 +  * $121=30.000
 +  * $122=10.000
 +  * $123=10.000
 +  * $130=125.000
 +  * $131=155.000
 +  * $132=150.000
 +  * $133=200.000
 +
 +M2: /dev/USB2
 +  * $0=10
 +  * $1=100
 +  * $2=0
 +  * $3=0
 +  * $4=0
 +  * $5=0
 +  * $6=0
 +  * $10=1
 +  * $11=0.020
 +  * $12=0.002
 +  * $13=0
 +  * $20=1
 +  * $21=0
 +  * $22=1
 +  * $23=1
 +  * $24=250.000
 +  * $25=1000.000
 +  * $26=250
 +  * $27=1.000
 +  * $30=12000
 +  * $31=0
 +  * $32=0
 +  * $100=10.000
 +  * $101=10.000
 +  * $102=250.000
 +  * $103=250.000
 +  * $110=1000.000
 +  * $111=1000.000
 +  * $112=500.000
 +  * $113=500.000
 +  * $120=100.000
 +  * $121=100.000
 +  * $122=10.000
 +  * $123=10.000
 +  * $130=165.000
 +  * $131=175.000
 +  * $132=200.000
 +  * $133=200.000
 +
 +
 +== Limit Switches ==
 +  * GND - Schwarz
 +  * VCC - Braun
 +  * SIG - Blau
 +
 ==== A4988 === ==== A4988 ===
 https://lastminuteengineers.com/a4988-stepper-motor-driver-arduino-tutorial/ https://lastminuteengineers.com/a4988-stepper-motor-driver-arduino-tutorial/
microct.1626386016.txt.gz · Last modified: by konstantin